Draw 3-4 glasses of water from spigot. Close up the housings. Turn OFF the blue tank ball valve on top of the water storage tank clockwise 90 degrees to mimic a full tank. Keep tank ball valve CLOSED and Turn ON the cold water supply as well as RO faucet lever. The faucet handle controls the flow of purified water exiting the faucet. Open housing: Have the RO standing upright. If your faucet comes with tubing attached: If your faucet comes without tubing attached: How To Replace Stages 1, 2, 3 Pre-Filters: General Installation/Operation/Maintenance Requirements. This will cushion any gap between the saddle and the pipe. Check drain water by pulling the black drain tubing out from the drain pipe and let water flow into a good size bucket to view it. So the drain water is forced-drained, not gravity-drained. If your RO feeds multiple output points (icemaker, bathroom, etc), please use a manual shut off valve to shut OFF water to those lines. Connect the Clear faucet tubing directly to system output. Copyright 2022 ManualsFile.com. All rights reserved. Turn on the RO faucet lever to relieve the built-up pressure inside the RO system. Discard 3 used filters, wash housings with mild soap, rinse off. But if that is not feasible you can install the system anywhere where there is a cold water supply with sufficient water pressure for the chosen RO model, and an outlet to drain off the drain water from the system. Turn the handle to horizontal position to release the water and vertically to shut off. Wait up to 10 minutes, then check to see if the drain water starts slowing down to a stop. APEC Water RO-90 - 90 GPD Ultra Safe Reverse Osmosis Drinking Water Filter System - Use Manual - Use Guide PDF. Select the location of the hole and drill a 1/4 hole through one side of the drain pipe then put the self-adhesive black sponge around the hole location (See Fig. 
Next, align and install the drain saddle clip with the tubing connection port onto the black sponge. Attach the drain saddle to the drain pipe and tighten the two screws evenly. There is constant water pressure packed inside the RO system which blocks the drain water from backing-up into the system. If drain water stops running --> The RO is shutting off properly no additional test is needed. If you prefer to mount the system to the wall, please make sure it can be taken down easily for filter replacement. First hand tighten the housing, then use filter wrench to fully tighten each housing. Once the drain saddle is secured, push 1/4 black drain tubing into the Quick Connect fitting on the saddle. Input water pressure: most important factor, TDS (Total Dissolved Solids) Level Reads Higher Than Normal, There is a leak at the tank ball valve connection.
7A and 7B). Mount the faucet as shown in Fig. Do not over-tighten. See Fig.14 (Page 20). Space: Make sure there is sufficient space under the counter for installation (an area of about 17L x 6W x 18H for the system, 11D x 18H for tank). Please let purified water run for 10-15 minutes to relieve built-up pressure inside the RO unit. The RO system can stand in the sink cabinet without mounting, this makes future filter change easy and convenient. Note: For stainless steel sinks, we recommend reversing the black locating washer so the flat end is facing upwards for proper installation. Installation needs to comply with state and local laws and regulations. Mis-aligning these two holes will block the drain water and cause membrane damage. Make sure the hole on the sponge is thoroughly punched out, and is aligned to the hole on the saddle to complete the installation. If the housing is too tight, use a hammer and gently tap on the wrench handle to help turn the wrench. Turn OFF tank ball-valve. Slip the plastic wrench onto the 1st housing. Feed water temperature: 40 100 F (4-37 C), Do not connect this unit to hot water source. To test if your RO system is shutting down normally, please follow the steps below. Make sure the tubing is inserted inside the faucet stem at least 1/4 deep while screwing the compression nut Fig. 9B (Page 12). Feed Water: RO systems are designed to treat both hard and soft water and can handle incoming TDS levels up to 2,000 ppm. Mounting: No need to mount the RO system on the wall. This will make opening the housings easier. This reverse osmosis system contains a replaceable treatment component critical for effective re- duction of total dissolved solids. Looking down from a top view, you should open the housing turning clockwise. RO will start making water to fill tank. The drain saddle assembly should be installed above the trap and on the vertical or horizon- tal tailpiece. When the RO fails to shut off after tank is filled, drain water will keep running down the drain depleting the pre-filters, the membrane, and may lead to higher water bills. Systems certified for cyst reduction may be used on disinfected water that may contain filterable cysts. DO NOT use a Insert on the drain tubing. The RO system is best installed under the kitchen sink.
The RO system should shut off automatically when the tank is filled. System must be installed indoor away from possible environmental damage. Install the RO in a sheltered environment, avoid exposure to hot and cold weather or under direct sunlight. If necessary, lay RO down on the floor to get a better leverage. Put 3 new filters into their respective housings: sediment filter in stage-1, carbon block filters in stages 2 & 3. Make sure to align the drain saddle hole to the drilled hole perfectly. Make sure each housing has a black O-ring in the threaded groves. APEC Water Systems - Water Filtration Systems. Turn OFF cold water supply to RO system. Turn OFF the RO faucet lever and Turn ON the tank ball valve. To reduce the drainage noise, mount the drain line as low as possible above the trap, or on the horizontal tailpiece. Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after system. User manualWater Filter System forAPEC Water RO-90. 9D (Page 12). 9C (Page 12). Make sure the tube insert is pushed all the way into the tubing Fig. The product water shall be tested periodically to verify that system is performing satisfactorily. Use manuals file type: PDF.
- Hardcover Weekly Planner
- Steel-it Weldable Paint
- Wholesale Custom Temporary Tattoos
- Baguette Bag Urban Outfitters
- Automatic Grass Cutter Using Arduino
- Twitch Panels Examples
- Laser Engraving Service